Wednesday, November 10, 2010

Easy Christmas Stockings!



My new quilting bee met at my house this week, and Rita showed us how to make Christmas stockings.  I mentioned this to a quilting and blogging friend, and she suggested I post the directions.  So here goes!  Thanks to Rita for the clear directions.  And I believe she got them herself from yet another person!

I use the larger rotary cutter
for the long straight edges of the
stocking and then switch to
the smaller one for the curved
edges.
I don't know how I can duplicate the pattern here on this blog, but it is easy enough to draw off a stocking pattern.  Ours is 16" long from the top cuff area to the lowest part of the foot; the cuff area is 8" wide; and from toe to heel measures 11".  You can get 2 stockings, front and back, from 1/2 yard of fabric, if the fabric doesn't have a directional print.  You need a bit more for 2 if the print is directional, as my snowman fabric is in the demonstration photos below.  For the lining, you need the same amount.

Cutting:  Cut 2 from the lining fabric, 1 front, and 1 back (these can be different fabrics or the same, as my snowman stocking is).  Also cut one cuff 16" x 8".  And cut one loop 8" x 2 1/2".  I used the lining fabric for the cuff on the snowman stocking. 

Sewing:

Here the lining and the
stocking fabrics have just been cut
out.


1.  Stack the front and back right sides together and the lining right sides together.






2.  Stack and pin all 4 layers together.  Sew from cuff edge to cuff edge.  I used a seam that was a bit over 1/4", to make sure I got all 4 layers included in the seam.
Sewing around the stocking







3.  Reach into the stocking between the lining fabric and turn the stocking so that the lining is on the outside.



4.  Fold the loop in half lengthwise and press.  Then fold the raw edges into the fold line and press.  Put these pressed edges together and edge stitch.

Pinning the loop to the stocking, with
lining on the outside


5.  Pin the hanging loop at the heel edge seam, raw edge placed at cuff raw edge.  I put my loop to the side of the seam, opposite where the seam allowance is, to reduce bulk.



Seam on the cuff pressed open
6.  Sew the short edge cuff seam and press open.  You will have a tube.  Turn and fold so that the seam is on the inside. 






Pinning the cuff to the stocking lining;
stocking front and back still
on the inside.
7.   Place the cuff over the stocking (still with the lining on the outside) and pull it down so that all raw edges are even.  Pin the edges together.






8.  Sew around the top of the stocking.  I always reinforce the area where the loop is with another line of stitches. 

Sewing the cuff on








7.  Turn the stocking ride side out and turn the cuff down.  Voila!  Your stocking is finished!





3 comments:

  1. I could never make these stockings, but they sure are cute. As usual I like the blue with the little angels. The other prints are very nice, too. Especially, the green in your demo.

    ReplyDelete
  2. Well, I am ready to make those RIGHT NOW, only in miniature and velvet for book club surprises. Nancy, you could make them. Just do one step at a time. Alice is very clear, but even I got lost midway talking about the heel...and that was when I realized one can only hold so much in one's mind at a time. You just dive in, step by step. How nice to have a manageable project that will share the handmade niceties. Lucky BEE!

    ReplyDelete
  3. Good work, Alice. I'm so far behind in my sewing endeavors that these cute stockings will have to wait their turn in my sewing agenda :)

    ReplyDelete